What does my hot tub need?
Pick your tub's rated amps — from the nameplate or the manual — and get the breaker, wire size, GFCI and disconnect rules in seconds. Most full-size tubs are 40, 50 or 60 amps on 240 V.
Your tub's manual governs. If it names a breaker size, use that. This lookup shows the wire and protection that go with each size, under Section 68 of the Canadian Electrical Code as adopted in BC.
Your hot tub
A 50 or 60 A tub takes about half of a 100 A service. Before you buy, check whether your panel has room — the load calculator runs the Rule 8-200 service calculation.
Long run from the panel to the tub? Wire sizes below assume a short run. For a long one, check the voltage drop — a long run may need a larger wire.
What it needs
| Circuit | — |
| Breaker | — |
| Wire (copper) | — |
| GFCI protection | — |
| Disconnect | — |
| Receptacles nearby | — |
| Bonding | — |
An electrical permit and inspection are required — in Nanaimo that's Technical Safety BC. We handle the permit as part of the job.
More free tools: all our calculators and useful links in one place.
How the requirements work
- The manual governs. The tub manufacturer's installation instructions name the breaker size and the wiring method. Inspectors read the manual — if it says 50 A, the circuit is 50 A. This lookup matches wire and protection to the size the manual calls for.
- GFCI protection (Rule 68-068). The tub supply must have Class A ground fault protection — usually a GFCI breaker in the panel or in the spa disconnect. The GFCI device itself must sit at least 3 m from the water, unless it's behind a permanent barrier or built into a factory-built tub. A warning sign goes beside the switch, and the GFCI should be tested regularly.
- Disconnect (Rule 68-072). Every permanently connected tub needs a disconnecting means rated to interrupt the load: outside the dwelling, readily accessible, within sight of the tub or lockable if it isn't, and at least 1.5 m from the inside walls of the tub. Between 1.5 m and 3 m it must be GFCI-protected or behind a permanent barrier.
- Receptacles (Rule 68-064). No receptacles within 1.5 m of the inside walls of the tub. Receptacles between 1.5 m and 3 m must be GFCI-protected. An existing outdoor plug too close to the new tub has to move.
- Bonding (Rule 68-058). Metal parts in and around the tub are bonded so everything sits at the same potential. A tub placed directly on the ground needs a buried copper bonding ring around it — or, where a ring isn't possible and access is from a conductive surface, a non-conductive barrier within 1.5 m. Your electrician confirms what applies to your tub and base.
- Wire sizes. Copper conductors per CEC Table 2 at 75 °C terminations, on a dedicated circuit with nothing else on it. Aluminum needs larger sizes — your electrician sizes it. Long runs may need a larger wire for voltage drop (Rule 8-102).
Quick reference — all sizes
| Tub rating | Circuit | Breaker (GFCI) | Copper wire |
|---|---|---|---|
| 15 A plug-in | 120 V dedicated | 15 A, 1-pole | 14 AWG |
| 20 A | 240 V dedicated | 20 A, 2-pole | 12 AWG |
| 30 A | 240 V dedicated | 30 A, 2-pole | 10 AWG |
| 40 A | 240 V dedicated | 40 A, 2-pole | 8 AWG |
| 50 A | 240 V dedicated | 50 A, 2-pole | 6 AWG |
| 60 A | 240 V dedicated | 60 A, 2-pole | 6 AWG |
Please read this before relying on the result
This lookup gives general guidance only, under Section 68 of the Canadian Electrical Code as adopted in BC (2024 edition). It is not a substitute for the tub manufacturer's instructions, a design by a qualified person, an electrical permit, or an inspection.
Real installations depend on the tub model, the base and location, the wiring method, and details this tool can't see. Figures may contain errors. Harbour Electrical Services Ltd. isn't liable for decisions made from these results. If anything is unclear, or before you buy the tub or the wire, get it checked properly — that's a free conversation, not a commitment.
Getting a hot tub?
Tell us the tub and where it's going — we'll check the panel, the wire run, the disconnect spot and the bonding, handle the permit, and tell you straight what it takes. No obligation.